Arduino

Arduino Ethernet Shield 2

Name: Arduino Ethernet Shield 2
Brand: Arduino
SKU: A000024
Price: 28.95 EUR
Availability: InStock

€28,95

Product variants

Quantity

Pickup available at 2251 NW 41st Street

Usually ready in 1 hour

Overview

The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you!
*Requires an Arduino Board (not included)

Operating voltage 5V (supplied from the Arduino Board)
Ethernet Controller: W5500 with internal 32K buffer
Connection speed: 10/100Mb
Connection with Arduino on SPI port

You can find your board warranty information here.

Getting Started

In the Getting Started section, you can find all the information you need to configure your board, use the Arduino Software (IDE), and start to tinker with coding and electronics.

Need Help?

Learn more on the Ethernet Shield 2 in the Ethernet2 Library reference
Get assistance with your projects in the Arduino Forum
Contact us through our Customer Support

Tech specs

The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the (Wiznet W5500 Ethernet chip). The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it.

The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO Board.

The Ethernet Shield 2 has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard micro-SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the Shield contained a full-size SD card slot; this is not supported.

The Shield also includes a reset controller, to ensure that the W5500 Ethernet module is properly reset on power-up. Previous revisions of the Shield were not compatible with the Mega and needed to be manually reset after power-up. The current Shield supports a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable.
PoE module features as follows:

IEEE802.3af compliant
Input voltage range 36V to 57V
Overload and short-circuit protection
12V Output
High efficiency DC/DC converter: typ 85% @ 80% load
1500V isolation (input to output)

NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet

The Shield does not come with a built in PoE module, it is a separate component that must be added on. Arduino communicates with both the W5500 and SD card using the SPI bus (through the ICSP header). This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5500 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5500 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5500 and SD card share the SPI bus, only one at a time can be active. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5500, set digital pin 10 as a high output.

The Shield provides a standard RJ45 Ethernet jack.
The reset button on the Shield resets both the W5500 and the Arduino Board.
The Shield contains a number of information LEDs:
ON: indicates that the Board and Shield are powered
13 is the Arduino standard built in LED
ACT: flashes when RX or TX activity is present
LINK: indicates the presence of a network link and flashes when the Shield transmits or receives data

This shield also hosts Tinkerkit compatible connectors as follows:

2 TinkerKit connectors for two Analog Inputs (in white), connected to A2 and A3.
2 TinkerKit connectors for two Aanlog Outputs (in orange in the middle), connected to PWM outputs on pins D5 and D6.
2 TinkerKit connectors for the TWI interface (in white with 4 pins), one for input and the other one for output.

Conformities

The following Declarations of Conformities have been granted for this board:

UKCA

REACH

Dev board return policy

Development boards are specialty items that generally cannot be resold on return, especially if the firmware has been flashed. Defective boards can be replaced or returned for refund within 30 days of purchase. Non-defective boards can be returned in the same time frame if in like-new condition with a 20 percent restocking fee applied. If the board has had altered firmware or became bricked due to a non-standard firmware flash, the board may not be eligible for return.

Sales tax is required in many states and will be added at checkout if applicable to your delivery state. Tax exempt forms can be sent to our support department.

Shipping & Returns

FREE Standard shipping on all items shipped in the USA!
We are in Florida and ship to: USA, Australia, Austria, Canada, France, Germany, Israel, Netherlands, the United Kingdom, and other countries (see full list in cart).

Local pickup available in Gainesville, FL

Expedited shipping orders placed before 3PM EST weekdays will ship that day. Standard shipping orders ship within 1 business day.

Sales tax: shipments shipped to states in which we are registered to collect tax will have appropriate tax added at checkout. Tax exempt forms can be sent to our support staff who can activate exemption status.

Lost packages and insurance

International Shipping:

Shipping options are visible in cart by using the shipping estimator. Transit times posted are estimates. International packages are subject to customs holds and duty payment may be required by your government on delivery. The cost of duty is not reimbursable. Internatonal shipping charges are not refundable in the event of a return.

Returns

See item description for product specific return policies, and return policies vary by item.

Bulk/High Value Order Returns

Due to the labor required to package and ship bulk orders, as well as cost and stock issues involved in replenishing items, bulk orders of 5 pieces or more are not returnable unless the equipment is defective or mis-advertised, or a return period is prenegotiated. For non-defective returns over $500, a restocking fee may be deducted from the refund to cover bank or card processing fees.

Backorder/Preorder

Items on backorder or preorder will ship as estimated on the item page. You can cancel an order any time up until shipment. Orders with expedited shipping will arrive in the advertised time after the order ships, not after the order is placed.

Cancellations

If you want to cancel an order, please email or call us at (352) 372-9902. If your item has not been shipped, we will cancel the order and provide a full refund.